MAX4599ELT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-WFDFN |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Strip |
| Published | 2004 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Gold (Au) |
| Max Power Dissipation | 245mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | MAX4599 |
| Pin Count | 6 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Switch-on Time-Max | 45ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Height Seated (Max) | 0.8mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4599ELT+T Overview
The electrical component comes in 6-WFDFN packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Strip. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 6. The electronic part provides high-quality output because it has 1 channels. With a 3V voltage supply, the electrical component should be turned on and run. A total of 6 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPDT switching circuits. It consists of 1 circuits. Try searching for the analog switch ic with MAX4599 if you are looking for variants. As far as internal resistance is concerned, it has 60Ohm. Please refer to the datasheets for 6 pins functions. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. 2V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 1μA current. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. The analogue multiplexer may be damaged if voltage is greater than 1μA. 5V operating voltages can be used with this electrical part.
MAX4599ELT+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 200MHz
MAX4599ELT+T Applications
There are a lot of Maxim Integrated MAX4599ELT+T Analog Switches & Multiplexers ICs applications.
- Switching Systems
- HDTV
- Channelized and Unchannelized DS3 applications
- Cable PC
- Medical
- Medical Instrumentation
- Data Acquisition Systems
- Routers
- Data switching
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
