MAX4599EXT+T
| Parameters | |
|---|---|
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 245mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4599 |
| Pin Count | 6 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Turn On Delay Time | 30 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 35ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28.009329mg |
| Operating Temperature | -40°C~85°C TA |
MAX4599EXT+T Overview
This electronic part is conveniently packaged in 6-TSSOP, SC-88, SOT-363, making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Extended operating temperature around -40°C~85°C TA. In total, there are 6 terminations. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. It is injected into the electrical part body with 6 pins. Circuits based on SPDT switching are used to construct these analog switch ics. The multiplexer consists of 1 circuits. Search with MAX4599 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 60Ohm. To find out what the 6 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2V. For this digital switch to work, 1μA current would suffice. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It conducts in a 4-bit manner.
MAX4599EXT+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 200MHz
4-Bit
MAX4599EXT+T Applications
There are a lot of Maxim Integrated MAX4599EXT+T Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Precision data acquisition
- DVD-R
- USB 1.1 signal switching circuits
- Private Branch Exchange (PBX)
- Battery-powered systems
- SDH/SONET multiplexers
- ISDN NT1/TA
- Cable PC
- Low-Voltage
