MAX4600CAE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4600 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 10nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 160 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.25Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 160ns, 210ns |
| Charge Injection | -60pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -65dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4600CAE Overview
Due to its 16-SSOP (0.209, 5.30mm Width) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. Based on SPST - NO/NC switching circuits, these analog multiplexers work. 2 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX4600. The internal resistance of this digital multiplexer is 1.25Ohm. For functions related to 16 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 20V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 4.5V should be applied to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 500nA. Despite this switch's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX4600CAE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4600CAE Applications
There are a lot of Maxim Integrated MAX4600CAE Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Cell phones
- Relay Replacement
- High-Voltage
- Frame Relay Equipment
- Ultrasound
- Audio and video routing
- Cable PC
- Modems
- E1 Multiplexer
