MAX4600CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4600 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 10nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 160 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 160ns, 210ns |
| Charge Injection | -60pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -65dB @ 1MHz |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4600CPE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Temperatures around 0°C~70°C TA are extended for operation. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. A key feature of the 16 series is the inclusion of this electronic part as part of its design. These analog multiplexers are built based on SPST - NO/NC switching circuits. A 2 circuit is present in this switch device. Look for analog switch ic variants by searching with MAX4600. A 1.25Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 36V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 4.5V. When the digital multiplexer is charged above 500nA, damage can occur. There is no problem with using dual supply voltage, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. The electrical part can be operated at 18V voltage levels.
MAX4600CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4600CPE Applications
There are a lot of Maxim Integrated MAX4600CPE Analog Switches & Multiplexers ICs applications.
- Imaging
- Multiplexers
- Mechanical reed relay replacement
- PBX interfaces
- FTTH
- Residential Gateways, Home Gateway/Router
- Precision data acquisition
- T1/E1 Terminals
- Digital access cross connects
- Public switching systems
