MAX4601CAE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4601 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Length | 6.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4601CAE+T Overview
As the electronic part is packed in 16-SSOP (0.209, 5.30mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around 0°C~70°C TA. There are 16 terminations totally. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. A total of 16 pins are injected into the body of the electronic part. Multiplexers built on a SPST - NC switching circuit are built. The multiplexer consists of 4 circuits. If you are looking for variants of the digital switch, trying search with MAX4601. Internally, this switch multiplexer has a resistance of 2.5Ohm. You can find the functions of the 16 pins in the datasheets. A voltage higher than 36V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. A digital multiplexer may suffer damage if voltage is applied above 500nA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. 20V operating voltages are supported by the electronic component.
MAX4601CAE+T Features
1 Channels
Switch Circuit: SPST - NC
MAX4601CAE+T Applications
There are a lot of Maxim Integrated MAX4601CAE+T Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Communication systems
- Avionics test equipment
- Intelligent PBX
- Fault Tolerant Systems
- Cable PC
- Audio signal routing
- DSLAMs
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Signal routing between systems
