MAX4602CAE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4602 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Normal Position | NO |
| Height | 1.78mm |
| Length | 6.33mm |
| Width | 5.38mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4602CAE Overview
Presented in 16-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 16. Due to its 4 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is injected into the electrical part body with 16 pins. Based on SPST - NO switching circuits, these analog multiplexers work. Search with MAX4602 if you are looking for analog multiplexer variants. An switch multiplexer with 2.5Ohm internal resistance has a value of 2.5Ohm. Please refer to the datasheets for 16 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. The analogue multiplexer may be damaged if voltage is greater than 500nA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. A voltage of 20V can be used to operate the electronic component.
MAX4602CAE Features
4 Channels
Switch Circuit: SPST - NO
MAX4602CAE Applications
There are a lot of Maxim Integrated MAX4602CAE Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- USB 1.1 signal switching circuits
- Microprocessor controlled systems
- Automotive applications
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cell phones
- Cable Modem
- 65 V DACs
- Optical Applications
- Avionics test equipment
