MAX4602CPE+
| Parameters | |
|---|---|
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4602 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
MAX4602CPE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. It is part of the design of the 16 series that this electronic component is included. A SPST - NO switching circuit is used to build these analog multiplexers. The circuits in this analogue multiplexer number 4. Try searching for MAX4602 variants of the analog switch ic. In this multiplexer, the internal resistance is 2.5Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 4.5V as the lowest voltage for the electrical part. A voltage higher than 500nA may cause damage to the switch multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electrical part can be operated at 20V voltage levels.
MAX4602CPE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4602CPE+ Applications
There are a lot of Maxim Integrated MAX4602CPE+ Analog Switches & Multiplexers ICs applications.
- SONET
- DSUs
- Microwave transmission systems
- Sample-and-hold systems
- Routers
- Fiber In The Loop (FITL)
- RGB switches
- Avionics
- 65 V DACs
- Data switching
