MAX4602CWE+T
| Parameters | |
|---|---|
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 350 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Normal Position | NO |
| Height Seated (Max) | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Weight | 200.686274mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4602 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
MAX4602CWE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.295, 7.50mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. Temperatures around 0°C~70°C TA are extended for operation. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. On the other hand, analog switches can be constructed using SPST - NO switching circuits. There are 4 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4602. It has an internal resistance of 2.5Ohm. The datasheets for the 16 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended that the electrical component receives a voltage of 4.5V. It may damage the digital multiplexer if the voltage is higher than 500nA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. A dual power supply should have at least 4.5V voltage attached. SEPARATE OUTPUT outputs are utilized by this digital multiplexer.
MAX4602CWE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4602CWE+T Applications
There are a lot of Maxim Integrated MAX4602CWE+T Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Avionics and Military Systems
- Transmit
- Audio and video switching
- Communication systems
- Precision test equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- USB 1.1 signal switching circuits
- Industrial control systems
- Cell phones
