Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.209, 5.30mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4602 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
350 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
56 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
55pF 55pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
250ns, 350ns |
Charge Injection |
120pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-59dB @ 1MHz |
Normal Position |
NO |
Height Seated (Max) |
1.99mm |
Length |
6.2mm |
Width |
5.29mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4602EAE+T Overview
The electrical component comes in 16-SSOP (0.209, 5.30mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. The total number of terminations is 16. As a result of its 1 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 16 series. A SPST - NO switching circuit is used to build these analog multiplexers. A total of 4 circuits make up this switch device. MAX4602 can be used to search for analog multiplexer variants. It has an internal resistance of 2.5Ohm. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 4.5V. When the digital multiplexer is charged above 500nA, damage can occur. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 4.5V to your dual power supply. There are SEPARATE OUTPUT outputs on this analog switch ic. 20V operating voltages can be used with this electrical part.
MAX4602EAE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4602EAE+T Applications
There are a lot of Maxim Integrated MAX4602EAE+T Analog Switches & Multiplexers ICs applications.
- Cable Modem
- SDH/SONET multiplexers
- Video signal routing
- PBXs
- PBX interfaces
- Digital cross connects (DSX-1)
- Audio signal routing
- DVD-R
- 65 V DACs
- Automotive applications