MAX4602EWE+
| Parameters | |
|---|---|
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Normal Position | NO |
| Height Seated (Max) | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4602 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
MAX4602EWE+ Overview
The electrical component comes in 16-SOIC (0.295, 7.50mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. 16 pins are injected to the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. This multiplexer is composed of 4 circuits. MAX4602 can be used to search for analog multiplexer variants. This digital multiplexer has 2.5Ohm internal resistance. The functions of 16 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 4.5V. When the digital multiplexer is charged above 500nA, damage can occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. In the case of dual power supplies, you should connect at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. The electronic component can function from 20V.
MAX4602EWE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX4602EWE+ Applications
There are a lot of Maxim Integrated MAX4602EWE+ Analog Switches & Multiplexers ICs applications.
- PDAs
- Video switching
- Digital cross connects (DSX-1)
- Multi-Line E1 Interface Cards
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Low-Voltage
- Frame Relay Equipment
- Optical Applications
- Cell phones
- DVD-R
