Parameters |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.295, 7.50mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
2.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
571mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX4602 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
20V |
Power Supplies |
12/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
5μA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
350 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
56 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
55pF 55pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
250ns, 350ns |
Charge Injection |
120pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-59dB @ 1MHz |
Normal Position |
NO |
Height Seated (Max) |
2.65mm |
Length |
10.3mm |
Width |
7.5mm |
MAX4602EWE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.295, 7.50mm Width), making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. As a result of its 1 channels, this electronic component provides high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. A SPST - NO switching circuit is used for these analog switches. 4 circuits are used in this analogue multiplexer. MAX4602 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 2.5Ohm. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 4.5V. If put voltage greater than 500nA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It can operate from 20V operating voltages.
MAX4602EWE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4602EWE+T Applications
There are a lot of Maxim Integrated MAX4602EWE+T Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Precision data acquisition
- T1/E1 Terminals
- Wireless Local Loop
- SONET/SDH ADM
- High speed data transmission line cards
- Audio and video switching
- Power routing
- PDAs
- Automatic test equipment