MAX4603CAE+T
| Parameters | |
|---|---|
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Length | 6.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4603 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
MAX4603CAE+T Overview
Presented in 16-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around 0°C~70°C TA. The total number of terminations is 16. Due to its 1 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 15V voltage supply. The electrical component body receives 16 pins. Multiplexers built on a SPST - NO/NC switching circuit are built. There are 4 circuits in this switch device. Try searching with MAX4603 to find analog multiplexer variants. There is 2.5Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage the electronic part should receive is 4.5V. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. A voltage of 20V can be used to operate the electronic component.
MAX4603CAE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4603CAE+T Applications
There are a lot of Maxim Integrated MAX4603CAE+T Analog Switches & Multiplexers ICs applications.
- Automotive applications
- SDH/SONET multiplexers
- PBXs
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- ISDN NT1/TA
- Microprocessor controlled systems
- SONET
- High-Voltage
- Microprocessor Controlled Analog Systems
- Communications systems
