MAX4603CWE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4603 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Height Seated (Max) | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4603CWE Overview
Presented in 16-SOIC (0.295, 7.50mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tube is used. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. Total terminations are 16. By its 1 channels, the electronic component provides high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 16 pins. Unlike digital switches, these are based on SPST - NO/NC switching circuits. A 4 circuit is present in this switch device. Try searching for the analog switch ic with MAX4603 if you are looking for variants. Internally, this switch multiplexer has a resistance of 2.5Ohm. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 36V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. 4.5V is the lowest voltage the electrical component should receive. It may damage the digital multiplexer if the voltage is higher than 500nA. There is no problem with using dual supply voltage, but it should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. This analog switch ic utilizes SEPARATE OUTPUT output. The electrical part can be operated at 20V voltage levels.
MAX4603CWE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4603CWE Applications
There are a lot of Maxim Integrated MAX4603CWE Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Power routing
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fault Tolerant Systems
- Avionics and Military Systems
- Relay replacements
- PDAs
- Industrial control systems
- Cross Connects
- SDH
