MAX4603CWE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4603 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Height Seated (Max) | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4603CWE+T Overview
As the electronic part is packed in 16-SOIC (0.295, 7.50mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature around 0°C~70°C TA extended. Total terminations are 16. A 1 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. There are 4 circuits in this switch device. Using the MAX4603 search parameter, you can discover variants of the switch. Analog switches have 2.5Ohm internal resistance. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 4.5V. It may damage the digital multiplexer if the voltage is higher than 500nA. Despite this switch's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. There is a voltage range of 20V operating voltages for the electrical part.
MAX4603CWE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4603CWE+T Applications
There are a lot of Maxim Integrated MAX4603CWE+T Analog Switches & Multiplexers ICs applications.
- Medical systems
- Digital Cross-Connects
- Cross Connects
- New designs requiring multiplexer functions
- MP3 players
- Cable Modem
- Precision data acquisition
- Channelized and Unchannelized DS3 applications
- Cable PC
- Signal routing between systems
