MAX4603EAE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4603 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 200mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Length | 6.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4603EAE+T Overview
The electrical component comes in 16-SSOP (0.209, 5.30mm Width) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. A 15V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. 4 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX4603. This digital multiplexer has 2.5Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. If you put voltage higher than 500nA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. Operating voltages range from 20V.
MAX4603EAE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4603EAE+T Applications
There are a lot of Maxim Integrated MAX4603EAE+T Analog Switches & Multiplexers ICs applications.
- MP3 players
- Mechanical reed relay replacement
- USB 1.1 signal switching circuits
- E1 Network Equipment
- DSUs
- Digital cross connects (DSX-1)
- T1/E1 Terminals
- DSLAMs
- Private Branch Exchange (PBX)
- SONET
