MAX4603EPE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4603 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 200mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 56 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 55pF 55pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 350ns |
| Charge Injection | 120pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -59dB @ 1MHz |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4603EPE Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, 16 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Multiplexers built on a SPST - NO/NC switching circuit are built. The multiplexer consists of 4 circuits. Use MAX4603 to search for variants of the digital switches. Analog switches have 2.5Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 36V to a switch device. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 4.5V should be applied to the electronic component. Put voltage above 500nA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. Operating voltages of 20V are compatible with the electrical part.
MAX4603EPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4603EPE Applications
There are a lot of Maxim Integrated MAX4603EPE Analog Switches & Multiplexers ICs applications.
- Central office
- Cell phones
- Video switching
- SONET
- Voice over IP/DSL – Integrated Access Devices, Smart
- PDH Multiplexers
- Audio and video signal routing
- Ultrasound
- Isolation
- Avionics
