Parameters |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4604 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
5/30/+-5/+-15V |
Number of Channels |
4 |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
1nA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
120 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
130 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
4Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
34pF 34pF |
On-state Resistance Match-Nom |
0.2Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
120ns, 130ns |
Charge Injection |
225pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Crosstalk |
-60dB @ 1MHz |
Switch-on Time-Max |
220ns |
Normal Position |
NC |
Length |
19.175mm |
Width |
7.62mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4604CPE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around 0°C~70°C TA. In total, 16 terminations have occurred. By its 4 channels, the electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. The analog switch ics are built using SPST - NC switching circuits. Try searching with MAX4604 if you're looking for variants. Internally, this switch multiplexer has a resistance of 4Ohm. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 20V to a switch device. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 4.5V is the lowest voltage that should be fed to the electronic electronic part. Putting voltage greater than 500nA on the multiplexer may cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4604CPE Features
4 Channels
Switch Circuit: SPST - NC
MAX4604CPE Applications
There are a lot of Maxim Integrated MAX4604CPE Analog Switches & Multiplexers ICs applications.
- SONET
- Digital Cross-Connects
- Central office
- MP3 players
- Multiplexers
- Remote Powered Equipment
- Audio and video signal routing
- T1/E1 Terminals
- CSU
- Multi-Line E1 Interface Cards