MAX4604EPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4604 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 220 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 120ns, 130ns |
| Charge Injection | 225pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4604EPE Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. There are 16 terminations totally. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 16 pins. SPST - NC switching circuits are used in these analog switch ics. A 4 circuit is present in this switch device. Try searching for MAX4604 variants of the analog switch ic. This digital multiplexer has 4Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage the electronic part should receive is 4.5V. Putting voltage greater than 500nA on the multiplexer may cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 18V operating voltages can be used with this electrical part.
MAX4604EPE Features
1 Channels
Switch Circuit: SPST - NC
MAX4604EPE Applications
There are a lot of Maxim Integrated MAX4604EPE Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Microprocessor Controlled Analog Systems
- Channel Banks
- Precision data acquisition
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Battery Powered Systems
- SDH/SONET multiplexers
- PDAs
- Sample hold systems
- Fiber In The Loop (FITL)
