MAX4604ESE+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4604 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 220 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 120ns, 130ns |
| Charge Injection | 225pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4604ESE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the electrical part body. SPST - NC switching circuits are used in these analog switch ics. Circuits number 4 make up this analogue multiplexer. Try searching for MAX4604 variants of the analog switch ic. A 4Ohm internal resistance characterizes this multiplexer. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. In order for the electronic part to function properly, the lowest voltage should be 4.5V. A digital multiplexer may suffer damage if voltage is applied above 500nA. Despite this switch's dual supply capability, its voltage should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. It can operate from 18V operating voltages.
MAX4604ESE+T Features
1 Channels
Switch Circuit: SPST - NC
MAX4604ESE+T Applications
There are a lot of Maxim Integrated MAX4604ESE+T Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Audio and video signal routing
- Data Acquisition Systems
- RGB switches
- T1/E1 Terminals
- High-Voltage
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fault Tolerant Systems
- Power routing
