MAX4605CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4605 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 120ns, 130ns |
| Charge Injection | 225pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 220ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4605CPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around 0°C~70°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on SPST - NO switching circuits. The multiplexer consists of 4 circuits. MAX4605 can be used to search for analog multiplexer variants. This digital multiplexer has 4Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. 4.5V is the lowest voltage that should be fed to the electronic electronic part. For this switch, a dual supply voltage is feasible, but it must not exceed 20VThe voltage should be at least 4.5V if you are using dual power supplies. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4605CPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4605CPE Applications
There are a lot of Maxim Integrated MAX4605CPE Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Sample-and-hold systems
- Switching Systems
- Avionics and Military Systems
- Fiber to the Home
- FTTH
- Modems
- T1/E1 Terminals
- Microwave transmission systems
- Data switching
