MAX4605EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4605 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 120ns, 130ns |
| Charge Injection | 225pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 220ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4605EPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. The multiplexer is located in Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. The total number of terminations is 16. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. A SPST - NO switching circuit is used to build these analog multiplexers. The multiplexer consists of 4 circuits. Use MAX4605 to search for variants of the digital switches. Analog switches have 4Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. The lowest voltage fed to the electronic component should be 4.5V. There is no problem with using dual supply voltage, but it should not exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. This analog switch ic utilizes SEPARATE OUTPUT output.
MAX4605EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX4605EPE Applications
There are a lot of Maxim Integrated MAX4605EPE Analog Switches & Multiplexers ICs applications.
- Medical
- HDTV
- Wireless Local Loop
- PBX interfaces
- USB 1.1 signal switching circuits
- Industrial control systems
- New designs requiring multiplexer functions
- Isolation
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
