MAX4606CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 4Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4606 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 120ns, 130ns |
| Charge Injection | 225pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Switch-on Time-Max | 220ns |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4606CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around 0°C~70°C TA. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. SPST - NO/NC switching circuits are used in these analog switch ics. There are 4 circuits in this multiplexer. Search with MAX4606 if you are looking for analog multiplexer variants. It has an internal resistance of 4Ohm. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. The lowest voltage the electronic part should receive is 4.5V. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX4606CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4606CPE Applications
There are a lot of Maxim Integrated MAX4606CPE Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Mechanical reed relay replacement
- DVD-R
- Public switching systems
- Microprocessor Controlled Analog Systems
- Optical Applications
- Audio and video routing
- Communication systems
- Central office
- FTTH
