Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
4Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4606 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Power Supplies |
5/30/+-5/+-15V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
36V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
1nA |
Max Supply Current |
500nA |
Throw Configuration |
SPST |
Turn On Delay Time |
220 ns |
Voltage - Supply, Single/Dual (±) |
4.5V~36V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
160 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
4Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
62 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
34pF 34pF |
On-state Resistance Match-Nom |
0.2Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
120ns, 130ns |
Charge Injection |
225pC |
Channel-to-Channel Matching (ΔRon) |
200m Ω |
Crosstalk |
-60dB @ 1MHz |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4606CSE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, 16 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 16 series. Multiplexers built on a SPST - NO/NC switching circuit are built. A total of 4 circuits make up this switch device. Try searching with MAX4606 to find analog multiplexer variants. A 4Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual, Single supply type. In order for the electronic part to function properly, the lowest voltage should be 4.5V. If put voltage greater than 500nA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 20V operating voltages can be used with this electrical part.
MAX4606CSE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4606CSE+ Applications
There are a lot of Maxim Integrated MAX4606CSE+ Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Battery Powered Systems
- PBX interfaces
- Medical systems
- SONET
- Communications systems
- MP3 players
- Fiber to the Home
- SDH
- 65 V DACs