MAX4606CSE+T
| Parameters | |
|---|---|
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 70°C |
| Min Operating Temperature | 0°C |
| HTS Code | 8542.39.00.01 |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4606 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/30/+-5/+-15V |
| Temperature Grade | COMMERCIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 220 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| Min Dual Supply Voltage | 4.5V |
| Off-state Isolation-Nom | 62 dB |
| On-state Resistance Match-Nom | 0.2Ohm |
| Height Seated (Max) | 1.75mm |
MAX4606CSE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. Search with MAX4606 if you are looking for analog multiplexer variants. A 4Ohm internal resistance characterizes this multiplexer. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 36V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 4.5V as the lowest voltage for the electrical part. When the digital multiplexer is charged above 500nA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. 18V operating voltages can be used with this electrical part. Temperatures over 70°C should not be allowed for the multiplexer to operate.
MAX4606CSE+T Features
1 Channels
MAX4606CSE+T Applications
There are a lot of Maxim Integrated MAX4606CSE+T Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Medical
- FTTH
- Low-Voltage
- E1 Multiplexer
- Microwave transmission systems
- Private Branch Exchange (PBX)
- Channelized and Unchannelized DS3 applications
- Digital cross connects (DSX-1)
- Cable Modem
