MAX4606ESE+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 4Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4606 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 220 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 4Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 34pF 34pF |
| On-state Resistance Match-Nom | 0.2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 120ns, 130ns |
| Charge Injection | 225pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -60dB @ 1MHz |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4606ESE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. The electronic part delivers high-quality output through its 1 channels. A 15V voltage supply should turn on and run the electronic component. Electronic part bodies are injected with 16 pins. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. Look for analog switch ic variants by searching with MAX4606. As far as internal resistance is concerned, it has 4Ohm. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. It is recommended to use 4.5V as the lowest voltage for the electrical part. If put voltage greater than 500nA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 18V operating voltages can be used with this electrical part.
MAX4606ESE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4606ESE+T Applications
There are a lot of Maxim Integrated MAX4606ESE+T Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Remote Powered Equipment
- Audio and video routing
- Precision data acquisition
- New designs requiring multiplexer functions
- Transmit
- Private Branch Exchange (PBX)
- Microwave transmission systems
- Precision test equipment
- High reliability control systems
