MAX4608ESE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4608 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 64pF 64pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 150ns |
| Charge Injection | 45pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4608ESE Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tube is used. The multiplexer is located in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -40°C~85°C TA. There are 16 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. A SPST - NO switching circuit is used for these analog switches. The multiplexer consists of 2 circuits. Search with MAX4608 if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 2.5Ohm. This switch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 20V. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage the electrical component should receive. Putting voltage greater than 500nA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. In the case of dual power supplies, you should connect at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
MAX4608ESE Features
1 Channels
Switch Circuit: SPST - NO
MAX4608ESE Applications
There are a lot of Maxim Integrated MAX4608ESE Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Cell phones
- Modems
- Intelligent PBX
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Switching Systems
- Precision test equipment
- ATM
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio/video switches
