MAX4608ESE+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 2.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MAX4608 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 64pF 64pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 150ns |
| Charge Injection | 45pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4608ESE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 16 pins. Unlike digital switches, these are based on SPST - NO switching circuits. There are 2 circuits in this switch device. If you are looking for variants of the digital switch, trying search with MAX4608. This digital multiplexer has 2.5Ohm internal resistance. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. 4.5V is the lowest voltage the electrical component should receive. When the digital multiplexer is charged above 500nA, damage can occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating voltages of 18V are compatible with the electrical part.
MAX4608ESE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4608ESE+T Applications
There are a lot of Maxim Integrated MAX4608ESE+T Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Remote wireless modules
- Intelligent PBX
- USB 1.1 signal switching circuits
- Modems
- PDAs
- Avionics test equipment
- Video switching
- Sample-and-hold systems
- Cross Connects
