MAX4609CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 2.5Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4609 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 2.5Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 64pF 64pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 150ns |
| Charge Injection | 45pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -66dB @ 1MHz |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4609CPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around 0°C~70°C TA extended. The total number of terminations is 16. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. As part of the design of the 16 series, this electronic part has been incorporated into the system. Multiplexers built on a SPST - NO/NC switching circuit are built. Circuits number 2 make up this analogue multiplexer. MAX4609 can be used to search for analog multiplexer variants. There is 2.5Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In normalcircumstances, users should not exceed 20V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. A low voltage of 4.5V should be applied to the electronic component. Putting voltage greater than 500nA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIn the case of dual power supplies, you should connect at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4609CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4609CPE Applications
There are a lot of Maxim Integrated MAX4609CPE Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- Residential Gateways, Home Gateway/Router
- Precision data acquisition
- Sample hold systems
- Cable Modem
- Microprocessor controlled systems
- ATM
- Fiber In The Loop (FITL)
- Signal routing between systems
- 65 V DACs
