MAX4610CSD

65ns, 28ns SPST - NO 100Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4610 14 Pins 100pA 3V 14-SOIC (0.154, 3.90mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4610CSD
Package: 14-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 747
Description: 65ns, 28ns SPST - NO 100Ohm DUAL Analog Switches BREAK-BEFORE-MAKE MAX4610 14 Pins 100pA 3V 14-SOIC (0.154, 3.90mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	14-SOIC (0.154, 3.90mm Width)
Number of Pins	14
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	14
ECCN Code	EAR99
Resistance	100Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Additional Feature	ALSO OPERATES AT 5V AND 12V VCC
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	3V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4610
Output	SEPARATE OUTPUT
Pin Count	14
Operating Supply Voltage	9V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	47 ns
Supply Type	Single
Turn-Off Delay Time	100 ns
-3db Bandwidth	300MHz
On-State Resistance (Max)	100Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	16pF 16pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	65ns, 28ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-80dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	90ns
Voltage - Supply, Single (V+)	2V~12V
Normal Position	NO
Height	1.5mm
Length	8.75mm
Width	4mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX4610CSD Overview

Shipping overseas is convenient with the electronic component packed in 14-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around 0°C~70°C TA. Total terminations are 14. Due to its 1 channels, the electrical component produces high-quality output. A 3V voltage supply should turn on and run the electronic component. The electrical component body receives 14 pins. A SPST - NO switching circuit is used to build these analog multiplexers. There are 4 circuits in this switch device. Try searching for the analog switch ic with MAX4610 if you are looking for variants. As far as internal resistance is concerned, it has 100Ohm. To find out what the 14 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The digital multiplexer has a low cost Single supply. There should be 2V voltage fed to the electrical part below 2V. This multiplexer would work with 1μA current. Using a single voltage supply, this switch device consumes 2V~12V volts. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages of 9V are compatible with the electrical part. Check out the electrical component's additional features, such as the following: ALSO OPERATES AT 5V AND 12V VCC.