Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Additional Feature |
ALSO OPERATES AT 5V AND 12V VCC |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4610 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Operating Supply Voltage |
9V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
47 ns |
Supply Type |
Single |
Turn-Off Delay Time |
100 ns |
-3db Bandwidth |
300MHz |
On-State Resistance (Max) |
100Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
16pF 16pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
65ns, 28ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
90ns |
Voltage - Supply, Single (V+) |
2V~12V |
Normal Position |
NO |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4610CUD Overview
Shipping overseas is convenient with the electronic component packed in 14-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tube. In Surface Mount, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there are 14 terminations. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. Into the electrical component body are injected 14 pins. Multiplexers built on a SPST - NO switching circuit are built. The multiplexer consists of 4 circuits. Look for analog switch ic variants by searching with MAX4610. There is 100Ohm internal resistance in this digital multiplexer. To find out what the functions of 14 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 2V. 1μA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. This analog switch ic utilizes SEPARATE OUTPUT output. The electrical part can be operated at 9V voltage levels. Don't miss this electronic component's additional features, such as: ALSO OPERATES AT 5V AND 12V VCC.
MAX4610CUD Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4610CUD Applications
There are a lot of Maxim Integrated MAX4610CUD Analog Switches & Multiplexers ICs applications.
- FTTH
- Digital access cross connects
- Communication systems
- Precision instrumentation
- Industrial control systems
- T1/E1 Terminals
- Cross Connects
- DVD-R
- Automatic test equipment
- High-Voltage