MAX4611CPD
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | ALSO OPERATES AT 5V AND 12V VCC |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4611 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 12V |
| Power Supplies | 3/12V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 28ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Length | 19.05mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4611CPD Overview
Due to its 14-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around 0°C~70°C TA. In total, 14 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. An electrical component like this is included in the 14 series. SPST - NC switching circuits are used in these analog switch ics. Circuits number 4 make up this analogue multiplexer. Try searching for MAX4611 variants of the analog switch ic. There is 100Ohm internal resistance in this digital multiplexer. The analogue multiplexer in this example is a typical Multiplexer or Switches. A analog switch ic that has a cost-effective Single supply type. For this digital switch to work, 1μA current would suffice. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. There is also ALSO OPERATES AT 5V AND 12V VCC to look out for in this electronic part.
MAX4611CPD Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4611CPD Applications
There are a lot of Maxim Integrated MAX4611CPD Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- Ultrasound
- Wireless Local Loop
- Multi-Line E1 Interface Cards
- Battery-powered systems
- Automotive applications
- Access Concentrators
- Low-Voltage
- Industrial and process control systems
- Imaging
