MAX4611CSD
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 100Ohm |
| Additional Feature | ALSO OPERATES AT 5V AND 12V VCC |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4611 |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 65 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 28 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 100Ohm |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 28ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4611CSD Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Surface Mount position. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. Total terminations are 14. A 1 channel electronic part produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. A total of 14 pins are injected into the body of the electronic part. A SPST - NC switching circuit is used for these analog switches. This multiplexer is composed of 4 circuits. Try searching with MAX4611 if you're looking for variants. This digital multiplexer has 100Ohm internal resistance. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Digital switch that provides Single power at a cost-effective price. The lowest voltage the electronic part should receive is 2V. 1μA current would be enough for this multiplexer to operate. Draining from a single voltage supply, this analog switch requires a voltage of 2V~12V. Put voltage above 1μA on the multiplexer to cause damage. Operating voltages range from 5V. Additional features include: ALSO OPERATES AT 5V AND 12V VCC.
MAX4611CSD Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4611CSD Applications
There are a lot of Maxim Integrated MAX4611CSD Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- DSLAMs
- SONET
- New designs requiring multiplexer functions
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Remote wireless modules
- Ultrasound
- Public switching systems
- Channel Banks
