MAX4611CSD+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | ALSO OPERATES AT 5V AND 12V VCC |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4611 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 12V |
| Power Supplies | 3/12V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 28ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| RoHS Status | ROHS3 Compliant |
MAX4611CSD+T Overview
Shipping overseas is convenient due to the electrical component's packing in 14-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. There are 14 terminations totally. High-quality output is provided by the electronic component's 1 channels. An 3V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 14 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. The multiplexer consists of 4 circuits. Look for analog switch ic variants by searching with MAX4611. Theswitch device is a typical Multiplexer or Switches. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. There is also ALSO OPERATES AT 5V AND 12V VCC to look out for in this electronic part.
MAX4611CSD+T Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4611CSD+T Applications
There are a lot of Maxim Integrated MAX4611CSD+T Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- Frame Relay Equipment
- Multiplexers
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Public switching systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cellular phones
- Isolation
- E1 Multiplexer
- Avionics and Military Systems
