MAX4611CUD
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Terminal Finish | TIN LEAD |
| Additional Feature | ALSO OPERATES AT 5V AND 12V VCC |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Pin Count | 14 |
| Supply Voltage-Max (Vsup) | 12V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 28ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switch-on Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
MAX4611CUD Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tube is used to provide high reliability. The multiplexer is located in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around 0°C~70°C TA extended. The total number of terminations is 14. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. A total of 14 pins are injected into the electrical part body. Circuits based on SPST - NC switching are used to construct these analog switch ics. A total of 4 circuits make up this switch device. A voltage of 2V~12V is required for this switch device, which drains from a single voltage source. This electronic part has additional features, such as: ALSO OPERATES AT 5V AND 12V VCC.
MAX4611CUD Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4611CUD Applications
There are a lot of Rochester Electronics, LLC MAX4611CUD Analog Switches & Multiplexers ICs applications.
- DSUs
- Power routing
- Digital cross connects (DSX-1)
- 65 V DACs
- SONET/SDH ADM
- Mechanical reed relay replacement
- Transmit
- Battery Powered Systems
- E1 Network Equipment
- Imaging
