MAX4611ESD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | ALSO OPERATES AT 5V AND 12V VCC |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4611 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 47 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 100 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 100Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 16pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 28ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4611ESD Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 14. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 3V, it should be turned on and run. There is an electrical component included in the 14 series. Multiplexers built on a SPST - NC switching circuit are built. There are 4 circuits in this switch device. Use MAX4611 to search for variants of the digital switches. As far as internal resistance is concerned, it has 100Ohm. Please refer to the datasheets for 14 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 12V to a switch device. The analog switch ic is of the Single supply type and is cost-effective. 2V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 1μA current. Using only a single voltage supply, this analog switch requires 2V~12V voltage. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Don't miss this electronic component's additional features, such as: ALSO OPERATES AT 5V AND 12V VCC.
MAX4611ESD Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4611ESD Applications
There are a lot of Maxim Integrated MAX4611ESD Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- DSUs
- E1 Network Equipment
- Automatic test equipment
- Cable Modem
- Fiber In The Loop (FITL)
- RGB switches
- Sample hold systems
- Cellular phones
- Mechanical reed relay replacement
