Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-SOIC (0.154, 3.90mm Width) |
Number of Pins |
14 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
Resistance |
100Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Additional Feature |
ALSO OPERATES AT 5V AND 12V VCC |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
245 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX4612 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
47 ns |
Supply Type |
Single |
Turn-Off Delay Time |
100 ns |
-3db Bandwidth |
300MHz |
On-State Resistance (Max) |
100Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
16pF 16pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
65ns, 28ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
90ns |
Voltage - Supply, Single (V+) |
2V~12V |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MAX4612CSD Overview
Due to its 14-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around 0°C~70°C TA. Totally, there are 14 terminations. This electronic part offers high-quality output due to its 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. There are 14 pins injected into the electronic part body. A SPST - NO/NC switching circuit is used to build these analog multiplexers. A total of 4 circuits make up this switch device. Look for analog switch ic variants by searching with MAX4612. Analog switches have 100Ohm internal resistance. To find out what the functions of 14 pins are, please refer to their datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. The analog switch ic is of the Single supply type and is cost-effective. 2V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 1μA current. This analogue multiplexer requires a voltage of 2V~12V when it drains from a single voltage supply. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Don't forget the additional features of this electronic part, such as: ALSO OPERATES AT 5V AND 12V VCC.
MAX4612CSD Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4612CSD Applications
There are a lot of Maxim Integrated MAX4612CSD Analog Switches & Multiplexers ICs applications.
- Channel Banks
- High reliability control systems
- Switching Systems
- Precision test equipment
- Cell phones
- Cross Connects
- Battery-powered systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Medical systems
- PBXs