Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
14 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Matte Tin (Sn) |
Additional Feature |
ALSO OPERATES AT 5V AND 12V VCC |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
3V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX4612 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Operating Supply Voltage |
9V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
47 ns |
Supply Type |
Single |
Turn-Off Delay Time |
100 ns |
-3db Bandwidth |
300MHz |
On-State Resistance (Max) |
100Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
16pF 16pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
65ns, 28ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
90ns |
Voltage - Supply, Single (V+) |
2V~12V |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4612CUD+ Overview
The electronic component is convenient to ship overseas because it is packed in a 14-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to 0°C~70°C TA. In total, there are 14 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. There are 14 pins injected into the electronic part body. A SPST - NO/NC switching circuit is used for these analog switches. The circuits in this analogue multiplexer number 4. If you are looking for variants of the digital switch, trying search with MAX4612. Internally, this switch multiplexer has a resistance of 100Ohm. Datasheets for 14 pin functions are available upon request. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. An effective Single supply digital multiplexer. There should be 2V voltage fed to the electrical part below 2V. It would be sufficient to run this analogue multiplexer with 1μA current. A voltage of 2V~12V is required to drain this analog switch from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. This analog switch ic utilizes SEPARATE OUTPUT output. A voltage of 9V can be used to operate the electronic component. This electronic part has additional features, such as: ALSO OPERATES AT 5V AND 12V VCC.
MAX4612CUD+ Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 300MHz
Additional Features: ALSO OPERATES AT 5V AND 12V VCC
MAX4612CUD+ Applications
There are a lot of Maxim Integrated MAX4612CUD+ Analog Switches & Multiplexers ICs applications.
- Relay replacements
- PBXs
- DVD-R
- Medical
- Video switching
- DSLAMs
- Automatic test equipment
- 65 V DACs
- Battery Powered Instruments
- Access Concentrators