MAX4613CSE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 70Ohm |
| Terminal Finish | TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4613 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~40V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 120ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4613CSE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around 0°C~70°C TA. In total, there have been 16 terminations. A electrical component with 1 channels is capable of high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. A SPST - NO/NC switching circuit is used for these analog switches. The multiplexer consists of 4 circuits. Try searching with MAX4613 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 70Ohm. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 40V. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 1μA current. It may damage the digital multiplexer if the voltage is higher than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. The electrical part can be operated at 18V voltage levels.
MAX4613CSE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX4613CSE+T Applications
There are a lot of Maxim Integrated MAX4613CSE+T Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Sample-and-hold systems
- E1 Multiplexer
- Communications systems
- Frame Relay Equipment
- 65 V DACs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- PBXs
- Ultrasound
- Precision test equipment
