MAX4613CUE+T

250ns, 120ns SPST - NO/NC 70Ohm Analog Switches BREAK-BEFORE-MAKE MAX4613 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4613CUE+T
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 430
Description: 250ns, 120ns SPST - NO/NC 70Ohm Analog Switches BREAK-BEFORE-MAKE MAX4613 16 Pins 500pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	4pF 4pF
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	250ns, 120ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	4 Ω (Max)
Crosstalk	-100dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	250ns
Switch-off Time-Max	120ns
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	70Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	457mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4613
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	18V
Power Supplies	12/+-15V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	40V
Min Supply Voltage	4.5V
Operating Supply Current	1μA
Nominal Supply Current	1nA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	400 ns
Voltage - Supply, Single/Dual (±)	4.5V~40V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	200 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	70Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	60 dB

MAX4613CUE+T Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. A switch device like this is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operation at a temperature around 0°C~70°C TA. In total, there have been 16 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 16 pins. The analog switch ics are built using SPST - NO/NC switching circuits. The multiplexer consists of 4 circuits. Using the MAX4613 search parameter, you can discover variants of the switch. It has an internal resistance of 70Ohm. Datasheets for 16 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. It is recommended to use 4.5V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. The analogue multiplexer may be damaged if voltage is greater than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. If you are using a dual power supply, you should attach at least 4.5V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 18V operating voltages are supported by the electronic component.