MAX4613EPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4613 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~40V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 4Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4613EPE Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. In total, there are 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. A 15V voltage supply should turn on and run the electronic component. As part of its design, the 16 series is equipped with this electronic component. Based on SPST - NO/NC switching circuits, these analog multiplexers work. There are 4 circuits in this switch device. Look for analog switch ic variants by searching with MAX4613. There is 70Ohm internal resistance in this digital multiplexer. To find out what the functions of 16 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 20V. Dual, Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 4.5V. This digital switch can be operated with a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX4613EPE Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX4613EPE Applications
There are a lot of Maxim Integrated MAX4613EPE Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Communication systems
- Relay Replacement
- DSUs
- Digital Cross-Connects
- Low-Voltage
- Precision data acquisition
- ISDN NT1/TA
- Wireless Local Loop
- RGB switches
