MAX4613EUE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 4.5V |
| Voltage - Supply, Single/Dual (±) | 4.5V~40V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 70Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 120ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4613EUE+ Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. A total of 16 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. A 15V voltage supply should turn on and run the electronic component. As part of the design of the 16 series, this electronic part has been incorporated into the system. On the other hand, analog switches can be constructed using SPST - NO/NC switching circuits. A total of 4 circuits make up this switch device. This digital multiplexer has 70Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 40V. 4.5V is the lowest voltage the electrical component should receive. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4613EUE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4613EUE+ Applications
There are a lot of Maxim Integrated MAX4613EUE+ Analog Switches & Multiplexers ICs applications.
- Wireless Local Loop
- Digital access cross connects
- Precision data acquisition
- Cross Connects
- MP3 players
- Channelized and Unchannelized DS3 applications
- E1 Network Equipment
- Signal routing between systems
- 65 V DACs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
