MAX4614EPD
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4614 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| -3db Bandwidth | 70MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 10ns |
| Charge Injection | 6.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Length | 19.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4614EPD Overview
Shipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. Mounted in Through Hole is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. 14 terminations have been made so far. High-quality output is provided by the electronic component's 4 channels. With a 3.3V voltage supply, the electrical component should be turned on and run. The electronic part body is injected with 14 pins. SPST - NO switching circuits are used in these analog switch ics. Try searching for the analog switch ic with MAX4614 if you are looking for variants. It has an internal resistance of 10Ohm. For details about the functions of 14 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 2V. For this multiplexer to operate, 1μA current would be sufficient. Using only a single voltage supply, this analog switch requires 2V~5.5V voltage. Putting voltage greater than 1μA on the multiplexer may cause damage. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. It can operate from 5V operating voltages.
MAX4614EPD Features
4 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 70MHz
MAX4614EPD Applications
There are a lot of Maxim Integrated MAX4614EPD Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- HDTV
- Fault Tolerant Systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Digital cross connects (DSX-1)
- Signal routing between systems
- PCMCIA cards
- Residential Gateways, Home Gateway/Router
- Battery Powered Instruments
- Relay replacements
