MAX4615CSD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4615 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Supply Type | Single |
| -3db Bandwidth | 70MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 10ns |
| Charge Injection | 6.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 15ns |
| Switch-off Time-Max | 12ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4615CSD Overview
The electrical component comes in 14-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. A total of 14 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. As part of its design, the 14 series is equipped with this electronic component. Circuits based on SPST - NC switching are used to construct these analog switch ics. A total of 4 circuits make up this switch device. Try searching for the analog switch ic with MAX4615 if you are looking for variants. As far as internal resistance is concerned, it has 10Ohm. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. An effective Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 2V. In order to operate this switch device, it would need a current of 1μA. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. This analog switch ic utilizes SEPARATE OUTPUT output. Don’t miss additional features of the electronic component such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
MAX4615CSD Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 70MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
MAX4615CSD Applications
There are a lot of Maxim Integrated MAX4615CSD Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Audio and video signal routing
- Residential Gateways, Home Gateway/Router
- Voice over IP/DSL – Integrated Access Devices, Smart
- Sample hold systems
- Remote Powered Equipment
- Industrial
- SONET
- E1 Network Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
