MAX4615EUD+T
| Parameters | |
|---|---|
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4615 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 15 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 12 ns |
| -3db Bandwidth | 70MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 10ns |
| Charge Injection | 6.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
MAX4615EUD+T Overview
Packed in 14-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 14 terminations. A electrical component with 1 channels is capable of high-quality output. With a 3.3V voltage supply, the electrical component should be turned on and run. An injection of 14 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NC switching circuits. 4 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX4615. Internally, this switch multiplexer has a resistance of 10Ohm. To find out what the 14 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. 2V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 1μA current. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electrical part can be operated at 5V voltage levels.
MAX4615EUD+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 70MHz
MAX4615EUD+T Applications
There are a lot of Maxim Integrated MAX4615EUD+T Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Precision test equipment
- Microprocessor controlled systems
- Precision instrumentation
- FTTH
- Audio and video signal routing
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Cell phones
- Remote Powered Equipment
- MP3 players
