MAX4616CPD+
| Parameters | |
|---|---|
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 10ns |
| Charge Injection | 6.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Length | 19.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4616 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 10 ns |
| -3db Bandwidth | 70MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
MAX4616CPD+ Overview
The electronic component is convenient to ship overseas because it is packed in a 14-DIP (0.300, 7.62mm). To ensure high reliability, a new packaging method Tube is used. Mounted in Through Hole is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. There are 14 terminations totally. The electronic part provides high-quality output because it has 4 channels. When a voltage supply of 3.3V is used, the electronic component should be turned on and run. An electrical component like this is included in the 14 series. SPST - NO/NC switching circuits are used in these analog switch ics. Try searching for the analog switch ic with MAX4616 if you are looking for variants. The internal resistance of this digital multiplexer is 10Ohm. Datasheets for 14 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. It is recommended to use 2V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1nA. This analog switch ic utilizes SEPARATE OUTPUT output. Check out the electrical component's additional features, such as the following: CAN ALSO OPERATE WITH 5 V SUPPLY.
MAX4616CPD+ Features
4 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 70MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
MAX4616CPD+ Applications
There are a lot of Maxim Integrated MAX4616CPD+ Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Remote Powered Equipment
- Avionics
- Cross Connects
- Signal routing between systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Battery Powered Instruments
- CSU
- Digital cross connects (DSX-1)
- Industrial control systems
