MAX4616CUD+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4616 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 10 ns |
| -3db Bandwidth | 70MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 10ns |
| Charge Injection | 6.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4616CUD+T Overview
Shipping overseas is convenient due to the electrical component's packing in 14-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 14. Due to its 1 channels, the electrical component produces high-quality output. An 3.3V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 14 series. SPST - NO/NC switching circuits are used in these analog switch ics. The multiplexer consists of 4 circuits. Use MAX4616 to search for variants of the digital switches. In this multiplexer, the internal resistance is 10Ohm. The datasheets for the 14 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. A analog switch ic that has a cost-effective Single supply type. It is recommended to use 2V as the lowest voltage for the electrical part. The analogue multiplexer could operate on 1μA current. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. If you put voltage higher than 1nA on the digital multiplexer, damage may occur. There are SEPARATE OUTPUT outputs on this analog switch ic. You shouldn't miss the additional features of the electrical component, such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
MAX4616CUD+T Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 70MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
MAX4616CUD+T Applications
There are a lot of Maxim Integrated MAX4616CUD+T Analog Switches & Multiplexers ICs applications.
- Communications systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Isolation
- E1 Network Equipment
- Fault Tolerant Systems
- Audio/video switches
- Routers
- Wireless Local Loop
- DSUs
- ATM
