MAX4616ESD
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATE WITH 5 V SUPPLY |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4616 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Power Supplies | 2.5/5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 10 ns |
| -3db Bandwidth | 70MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 12ns, 10ns |
| Charge Injection | 6.5pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 15ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4616ESD Overview
Presented in 14-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Operation at a temperature around -40°C~85°C TA. In total, 14 terminations have occurred. The electronic part delivers high-quality output through its 1 channels. With a 3.3V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 14 pins. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Circuits number 4 make up this analogue multiplexer. Use MAX4616 to search for variants of the digital switches. Analog switches have 10Ohm internal resistance. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 2V. It would be sufficient to run this analogue multiplexer with 1μA current. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. Putting voltage greater than 1nA on the multiplexer may cause damage. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. You shouldn't miss the additional features of the electrical component, such as: CAN ALSO OPERATE WITH 5 V SUPPLY.
MAX4616ESD Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
-3db Bandwidth: 70MHz
Additional Features: CAN ALSO OPERATE WITH 5 V SUPPLY
MAX4616ESD Applications
There are a lot of Maxim Integrated MAX4616ESD Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Sample-and-hold systems
- Battery Powered Instruments
- Central office
- Audio signal routing
- Industrial
- New designs requiring multiplexer functions
- MP3 players
- HDTV
- Cable PC
