MAX4617CUE+
| Parameters | |
|---|---|
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 533mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4617 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Throw Configuration | SP8T |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 27pF |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
MAX4617CUE+ Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. The operating temperature is extended to around 0°C~70°C TA. In total, 16 terminations have occurred. The electronic part delivers high-quality output through its 8 channels. When the electronic component is given a voltage of 3.3V, it should be turned on and run. Electronic part bodies are injected with 16 pins. Circuits number 1 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX4617. The internal resistance of this digital multiplexer is 10Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. normally, users should not supply switches with voltages higher than 5.5V. Analogue multiplexers of the Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. The analogue multiplexer could operate on 1μA current. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. 5V operating voltages are supported by the electronic component.
MAX4617CUE+ Features
8 Channels
1μA Supply Current
MAX4617CUE+ Applications
There are a lot of Maxim Integrated MAX4617CUE+ Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Intelligent PBX
- Channel Banks
- Video signal routing
- Audio and video switching
- Relay Replacement
- Automatic test equipment
- Routers
- DVD-R
- 65 V DACs
