MAX4617EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4617 |
| Pin Count | 16 |
| Power Supplies | 2.5/5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 27pF |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Signal Current-Max | 0.075A |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4617EPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. The advanced packaging method Tube provides high reliability. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 8:1. The operating temperature is extended to around -40°C~85°C TA. There are 16 terminations totally. As a result of its 8 channels, this electronic component provides high-quality output. A 3.3V voltage supply should turn on and run the electronic component. An electrical component like this is included in the 16 series. There are 1 circuits in this switch device. Try searching with MAX4617 if you're looking for variants. In this multiplexer, the internal resistance is 10Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. It is recommended that the electrical component receives a voltage of 2V. This analogue multiplexer requires a voltage of 2V~5.5V when it drains from a single voltage supply. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER.
MAX4617EPE Features
8 Channels
MAX4617EPE Applications
There are a lot of Maxim Integrated MAX4617EPE Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Optical Applications
- Video signal routing
- Industrial
- Relay replacements
- Industrial control systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio signal routing
- Power routing
- SONET/SDH ADM
