MAX4618CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Base Part Number | MAX4618 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Circuits | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 15 ns |
| Turn On Delay Time | 20 ns |
| Logic Function | Multiplexer |
| Supply Type | Single |
| Turn-Off Delay Time | 15 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 15pF |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 15ns, 10ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 200m Ω |
| Crosstalk | -96dB @ 100kHz |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4618CPE+ Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. The advanced packaging method Tube provides high reliability. It is mounted in the position Through Hole. Multiplexers and demultiplexers have the same number of circuits 4:1. Operating temperature around 0°C~70°C TA extended. This electrical component is included in the 16 series of products. SP4T switching circuits are used in these analog switch ics. It consists of 2 circuits. If you are looking for variants of the digital switch, trying search with MAX4618. There is 10Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 16 pins functions. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexers of the Single supply type that are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. In order to operate this switch device, it would need a current of 1μA. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. There is a voltage range of 5V operating voltages for the electrical part.
MAX4618CPE+ Features
Switch Circuit: SP4T
1μA Supply Current
MAX4618CPE+ Applications
There are a lot of Maxim Integrated MAX4618CPE+ Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Digital Cross-Connects
- Modems
- SDH/SONET multiplexers
- Microprocessor Controlled Analog Systems
- E1 Network Equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Sample-and-hold systems
- RGB switches
- Access Concentrators
